HyPer 9 IS &#8482; - SRIPM Integrated System

Sales Sheet

Performance Graph

DOWNLOAD CAD DRAWINGS

HyPer 9 ™ - SRIPM Motor

This motor has an 8.66" diameter and weighs 120 lbs. It is a Synchronous Reluctance Internal Permanent Magnet motor which produces 173 lb/ft peak torque. The HyPer 9 ™ Motor combines the torque producing forces of Permanent Magnets with the highly efficient and cost effective Synchronous Reluctance design.

Brushless Motor
Cageless Rotor - Higher Efficiency, No Heat
No Rotor Slip
Up to 95% Efficiency!
Up to 50% higher torque than similar sized AC Induction motors running at the same power levels!
Astounding performance in field weakening area with +50% power up to 5 times nominal speed
IP54 Protection
Robust and Reliable

The Drive End (DE) shaft is 1.125" in diameter with a 1/4" keyway.

You can adapt this motor to connect to a HyPerTrans 9i ™ Motor shaft! The motor has the same high efficiency as the HyPer 9i ™ Motor.

Delivery Time: From Stock.

Engineering Drawing

Performance Graph

DOWNLOAD CAD DRAWINGS

HyPer-Drive X1 ™ - SRIPM Motor Controller/Inverter

Equipped with the latest technology in power electronics, our HyPer-Drive X1 ™ Controller can drive SRIPM motors in a wide range of applications up to 85kw peak power. The X1 is the only controller smart enough to power our HyPer 9 ™ Motor, and can be configured to control many other AC motors!

DC supply voltage from 62V to 130V and current up to 750Amps max
Up to 50% higher power density than direct competitors (Superior power in half the footprint)
Field Oriented Control algorithm optimized specifically for Synchronous Reluctance Internal Permanent Magnet motors
Fully customizable I/O
IP65 protection - Robust and Reliable
Extensive program customization from PC with Smartview Software

Delivery Time: From Stock.

Engineering Drawing

User Manual

DOWNLOAD CAD DRAWINGS

HyPer 9D ™ - SRIPM Motor

This motor has an 8.66" diameter and weighs 120 lbs. The HyPer 9D ™ is a Dual Shaft version of our already impressive HyPer 9 ™ Motor. It is a Synchronous Reluctance Internal Permanent Magnet motor which produces 173 lb/ft peak torque. This industry leading technology combines highly efficient and cost effective Synchronous Reluctance design with the torque producing forces of Permanent Magnets.

Double ended Shaft
Encoder End shaft and bolt pattern match the Commutator End of WarP 9 ™ Motors
Brushless Motor
Cageless Rotor - Higher Efficiency, No Rotor Heat
No Rotor Slip
Up to 95% Efficiency
Up to 50% higher torque than similar sized AC Induction motors running at the same power levels
Astounding performance in field weakening area with +50% power up to 5 times nominal speed
IP54 Protection
Robust and Reliable

The Drive End (DE) shaft is 1.125" in diameter with a 1/4" keyway.

You can adapt this motor to connect to a HyPerTrans 9i ™ Motor shaft! The motor has the same high efficiency as the HyPer 9i ™ Motor.

Delivery Time: From Stock.

Engineering Drawing

Performance Graph

DOWNLOAD CAD DRAWINGS

WarP 7 ™ Motor

This motor has an 7.25" diameter. It is a series wound DC motor with a double ended shaft. Our WarP 7 ™ Motor has been designed for use in dual motor and EMIS applications and to ease the conversion process for people who want dual motor and/or direct drive applications. It has many unique features that set it apart from any other EV motor currently manufactured. Timing can be adjusted to CWDE or CCWDE(from the normal Neutral).

Both the Drive End (DE) shaft and the Commutator End (CE) shaft are 1.125" in diameter with a 1/4" keyway.

You can adapt this motor to connect to a TransWarP 7 ™ Motor CE shaft! The motor also has brush wear indicators and a temperature snap switch. It has the same high efficiency fan and massive commutator and brushes as the TransWarP 7 ™ Motor.

Delivery Time: From Stock.

00-08217
Drive End	Comm End
72V Advanced Data	72V Advanced Graph
48V Advanced Data	48V Advanced Graph
48V Neutral Graph	48V Neutral Data

WarP 8 ™ Motor

The WarP 8 ™ motor is basically a twin to the ADC 8" motor (203-06-4001A), but at a better price. As a convenience, we have even duplicated the mounting bolt pattern to allow our clients to utilize existing mounting plate adapters.

The WarP 8 ™ motor's basic parameters: It is an 8" diameter series wound DC motor with a double ended shaft. The motor utilizes large style comm's and brushes. The comm's are key-locked onto the drive shaft -- reducing the likelihood of lifting any commutator bars. Class "H" insulation is used throughout the motor. The drive shaft and tail shaft have standard keyways cut into them. The drive shaft comes with a pilot bearing hole and a 5/16 - 18 mounting hole.

"White Zombie" (driven by John Wayland) originally used two of our WarP 8 ™ motors. This car is the world's quickest and fastest "Street Legal Electric Vehicle".

Delivery Time: From Stock - replaced with the ImPulse 9 and ImPulse 8.

00-08200	00-08203
00-08206	00-08218
Performance Graph	Performance Data

ImPulse 9 ™ Motor

This is a 9.25" diameter, series wound DC motor with a double ended shaft and is pre-drilled to allow for brush advance in either Neutral, advanced CWDE or advanced CCWDE (standard). Our ImPulse 9 ™ Motor share many of the internal components found in our WarP 9 ™ Motor, but has the mounting pattern and pilot to match 8" motors (Model 00-08259 & Model 00-08269, Model 00-08249 does NOT match ADC 8" and is no longer a stocked item!). There is also a single ended shaft version of this motor - 00-08269.

The commutator bars are more securely attached to the arbor, so they will be less likely to lift. The drive shaft is bored for a pilot bearing and drilled & tapped for a 5/16 - 18 bolt. The tail shaft also has a 1/4 - 20 bolt hole to mount tach sensors or secure couplers and accessories. Again, we have duplicated the ADC 8" mounting bolt pattern allowing clients to use preexisting mounting adapters (Model 00-08259 & Model 00-08269) Model 00-08249 does NOT match the ADC 8" mounting pattern, but rather matches the ADC 9" bolt pattern. Class "H" insulation is used throughout the motor. The drive shaft and tail shaft have standard keyways cut into them. This motor is also available at a better price point to end users.

Delivery Time: From Stock.

00-08259NAL	00-08259
00-08269	00-08249
Performance Graph	Performance Data

WarP 9 ™ Motor

Our WarP 9 ™ motor is similar to the ADC 9" motor, but with numerous improvements. It is a 9.25" diameter, series wound DC motor with a double ended shaftOf the most notable changes, we have a larger com and utilize the large style brushes. Beginning with motors being manufactured in July, 2010 numerous enhacements are being added to our entire line of motors, some of which include:

• 1/2”-13 diameter terminal studs: Increased from 3/8” diameter - bigger is better!

New brush composition: Handles higher voltages and currents – improves motor efficiency

New brush design: “split brush with pad” design handles higher voltages and currents – improves motor efficiency

Increased spring pressure: Spring pressure has been increased to allow improved commutation (note: This does NOT increase brush-commutator wear as might be suspected)! Higher spring pressures allow for increased commutation – which improves commutator wear over “bouncing brushes”.

Addition of optical RPM sensor hole: A 1/2”-20 hole is drilled and tapped into the DE for easy insertion and use of an RPM sensor. (further information will be provided on appropriate sensors and gauges (RPM, temperature) in the near future.)

Addition of temperature thermistor: This will allow the motor temperature to be be monitored.

Removal of brush wear indicators: To the best of our knowledge, no one ever used this feature. As armature voltage was used for signaling it was difficult to adapt and use.

Improved fan: Increased air flow will allow the motors to run cooler and more efficiently. The 15- blade fan is a new casting that will make using the RPM sensor easier as well.

Drive End mounting holes changed from “blind holes” to thru holes. If the wrong length bolts were used it could damage the DE head. Care must still be exercised to ensure that the mounting bolts do not hit the fan blades!

Temperature snap switch and thermistor plug will use the same black plug that was previously used for the brush wear indicators and accepts 1/4”, flat spade connectors, but it will now be counterbored.

All of the above changes are being phased into production across ALL motors

The com bars are more securely attached to the arbor, so they will be less likely to lift. The drive shaft is bored for a pilot bearing and drilled & tapped for a 5/16 - 18 bolt. The tail shaft also has a 1/4 - 20 bolt hole to mount tach sensors or secure couplers and accessories. Again, we have duplicated the ADC 9" mounting bolt pattern allowing clients to use preexisting mounting adapters. Class "H" insulation is used throughout the motor. The drive shaft and tail shaft have standard keyways cut into them. This motor is also available at a better price point to end users.

Delivery Time: From Stock.

00-08219 Manufactured after 7/1/2010	00-08219 Manufactured prior 7/1/2010
Performance Graph Manufactured after 7/1/2010	Performance Data Manufactured after 7/1/2010
Performance Graph Manufactured prior 7/1/2010	Performance Data Manufactured prior 7/1/2010

WarP 11 ™ Motor

It is a 11.45" diameter, series wound DC motor with a double ended shaft. Our WarP 11 ™ motor comes set with advanced timing CCWDE. Of the most notable changes, we have a very large com and utilize the large style, very high quality brushes.

Delivery Time: From Stock.

00-08311 Manufactured after 7/1/2012	00-08311 Manufactured prior 7/1/2012
00-08511	00-08811
Drive End	Performance Graph
Performance Data

WarP 13 ™ Motor

This is a 13.25" diameter, series wound DC motor with a double ended shaft. Our WarP 13 ™ motor may be customized to a large extent by the customer. This motor can have its fields switched from serial to parallel! The engineers at Warfield Electric said: "This motor is Torque City" when it was dyno tested!

The com bars are more securely attached to the arbor, so they will be less likely to lift. The drive shaft is bored for a pilot bearing and drilled & tapped for a 1/2 - 13 bolt. The tail shaft also has a 1/4 - 20 bolt hole to mount tach sensors or secure couplers and accessories. This motor is a "foot-mount" and should not be considered for face mounting due to its weight. Class "H" insulation is used throughout the motor. The drive shaft and tail shaft may be specially designed or use standard keyways or splines.

Delivery Time: Special Order (generally 12-16 weeks after final approval of engineering).

00-08413	00-08513
Serial Performance	Parallel Performance
Serial Data	Parallel Data

TransWarP 7 ™ Motor

This motor has an 7.25" diameter. It is a series wound DC motor with a double ended shaft. Our TransWarP 7 ™ Motor has been designed for use in EMIS applications and to ease the conversion process for people who want dual motor and/or direct drive applications. It has many unique features that set it apart from any other EV motor currently manufactured. Timing can be adjusted to CWDE (from the normal CCWDE).

This motor has a "shorty" tail shaft housing from a Chevrolet Turbo 400 transmission fitted to the drive end-bell (may be ordered with or without housing!) This is because the drive end shaft is not the typical 1.125" single-keyed type, but rather a hefty 1.370", 32-tooth involute spline that is identical to the tail shaft spline of a Turbo 400 transmission. In other words, this motor was designed to replace a transmission and couple directly to a drive shaft!

We have added grease fittings (as you now have a slip-yoke assembly...). We use the industry standard 1350 universal, so you can easily adapt it to any manufacturers drive shaft! The motor also has brush wear indicators and a temperature snap switch. It has the same high efficiency fan and massive commutator and brushes as the WarP 7 ™ Motor.

Delivery Time: From Stock.

00-08207
Drive End	Comm End
72V Advanced Data	72V Advanced Graph
48V Advanced Data	48V Advanced Graph
48V Neutral Data	48V Neutral Graph

TransWarP 9 ™ Motor

This motor has an 9.25" diameter. It is a series wound DC motor with a double ended shaft. Our TransWarP 9 ™ motor has been designed to ease the conversion process for people who want dual motor and/or direct drive applications. It has many unique features that set it apart from any other EV motor currently manufactured.

We have added double wide bearings on the drive end, added grease fittings (as you now have a slip-yoke assembly...). We use the industry standard 1350 universal, so you can easily adapt it to any manufacturers drive shaft! The motor also has brush wear indicators and a temperature snap switch. It has the same high efficiency fan and massive commutator and brushes as the WarP 9 motor. We even made the commutator end shaft the same diameter as the drive end of a typical WarP 9 - just in case you wanted to connect 2, 9" motors together!

We also provide 2 lifting holes.

Delivery Time: From Stock.

00-08309	Performance Graph
Performance Data

TransWarP 11 ™ Motor

This motor has an 11.45" diameter. It is a series wound DC motor with a double ended shaft. Our TransWarP 11 ™ Motor has been designed to ease the conversion process for people who want direct drive applications. It has many unique features that set it apart from any other EV motor currently manufactured.

But we didn't stop there! We added double wide bearings on the drive end, added grease fittings (as you now have a slip-yoke assembly...). We chose the industry standard 1350 universal, so you can easily adapt it to any manufacturers drive shaft! We moved the terminals to the side of the motor to avoid road hazard damage, and to allow more clearance above and below. The motor also has brush wear indicators and a temperature snap switch. It has the same high efficiency fan and massive commutator and brushes as the WarP 11 motor. We even made the commutator end shaft the same diameter as the drive end of a typical WarP 11 - just in case you wanted to connect 2, 11" motors together!

If that wasn't enough, we also provide a lifting ring and 8 threaded mounting holes in the commutator end bell. This way you will find it easier to mount, as well as having a method of easily attaching a speed sensor, alternator, air conditioner, etc.

Delivery Time: From Stock.

00-08711 Manufactured after 9/1/2006	00-08711 Manufactured prior 9/1/2006
Performance Graph	Performance Data

WarP 11HV ™ Motor (Sales Sheet not yet available)

It is a 11.45" diameter, series wound DC motor with a double ended shaft. This is the currently the only motor in our product line that has inter-poles. Our WarP 11HV ™ motor comes set with neutral timing. Of the most notable changes, we have is a very large com and the use of very large style, very high quality brushes. A special order TransWarP 11HV version is also available!

Delivery Time: From Stock.

00-08911	Perfrmance Graph
Performance Data